TECHNICAL SERVICE REQUEST

* Compulsory fields

PRODUCT INFORMATION

JAMES HARDIE PRODUCTS (MULTIPLE PRODUCTS CAN BE SELECTED)

Artisan Lap Siding Artisan V-Groove Siding Artisan Trim Board Cempanel Vertical Siding (5/16" thick panel)

Hardie Reveal Panel (7/16 thick panel) Prevail Lap Siding Prevail Vertical Siding (5/16" thick panel) HardieBacker Board HardiePanel Vertical Siding (5/16" thick panel)

HardiePlank Lap Siding HardieShingle Siding HardieSoffit Panel HardieTrim Board HardieWrap Weather Barrier

Artisan Lap Siding

PLEASE STATE WIDTH*:

COLORPLUSTM TECHNOLOGY*:

Yes No

Artisan V-Groove Siding

COLORPLUSTM TECHNOLOGY*:

Yes No

Artisan Trim Board

COLORPLUSTM TECHNOLOGY*:

Yes No

Cempanel Vertical Siding (5/16" thick panel)

COLORPLUSTM TECHNOLOGY*:

Yes No

Hardie Reveal Panel (7/16 thick panel)

Fastener Type:

Exposed Concealed

COLORPLUSTM TECHNOLOGY*:

Yes No

Prevail Lap Siding

PLEASE STATE WIDTH:

COLORPLUSTM TECHNOLOGY*:

Yes No

Prevail Vertical Siding (5/16" thick panel)

COLORPLUSTM TECHNOLOGY*:

Yes No

HardieBacker Board

 

HardiePanel Vertical Siding

Please specify the vertical joint treatment method to be used:

Please select from the list, If applicable Moderate Contact Joint Caulked Joint (not applicable with ColorPlus) Battened Joint Expressed Joint or third-party aluminium trim

COLORPLUSTM TECHNOLOGY*:

Yes No

HardiePlank Lap Siding

PLEASE STATE WIDTH:

COLORPLUSTM TECHNOLOGY*:

Yes No

HardieShingle Siding

COLORPLUSTM TECHNOLOGY*:

Yes No

HardieSoffit Panel

COLORPLUSTM TECHNOLOGY*:

Yes No

HardieTrim Board

COLORPLUSTM TECHNOLOGY*:

Yes No

HardieWrap Weather Barrier

COLORPLUSTM TECHNOLOGY*:

Yes No

PROJECT INFORMATION

STUD TYPE*:

Please select a stud type Wood Metal Other (user must fill in field)

OTHER*:

STUD SPACING*:

Inches on center

WOOD STUD SPECIES OR METAL STUD GAUGE (IF APPLICABLE):

RAINSCREEN OR STRUCTURAL
FURRING*:

Yes No

WOOD:

METAL:

OTHER:

 

WOOD FURRING SPECIES (IF APPLICABLE):

 

 

METAL FURRING GAUGE (IF APPLICABLE):

 

GYPSUM WALL BOARD SHEATHING*:

Yes No

Gypsum wallboard sheathing thickness:

Inches

EXTERIOR INSULATION*:

Yes No

EXTERIOR RIGID FOAM SHEATHING:

Exterior Insulation Thickness:

Inches

MINERAL WOOL INSULATION:

OSB OR WOOD STRUCTURAL PANEL*:

Yes No

OSB or WSP thickness:

Inches

Which layer is the OSB/WSP?:

Outermost layer Innermost layer (next to studs) Other: Please describe the layers if selecting "Other"

CODE YEAR ON PERMIT*:

CODE NAME ON PERMIT (IBC, IRC, ETC.)*:

MEAN BUILDING ROOF HEIGHT (FT)*:

Mean Roof height is the average of the roof eave height and the height to the highest point on the roof surface, (except that, for roof angles of less than or equal to 10 degrees, the mean roof height shall be the roof eave heigh), as measured from the mid-point of the grade slope, or from flat grade if not sloped.

IF MEAN BUILDING ROOF HEIGHT IS ≤ 60 FEET

WIND DESIGN LOAD (MPH)*:

WIND EXPOSURE CATEGORY*:

Please select “N/A” if mean building roof height is > 60 feet.

B C D N/A

If project has non-nailable substrates greater than 1 in. Please provide the Wind Design Pressure (PSF).

 

IF MEAN BUILDING ROOF HEIGHT IS > 60 FEET

DESIGN PRESSURE (PSF) i

Please enter the design pressure for Wall Zone
5 based on Effective Wind Area of 10 SQFT.

ASD-

ASD+ i

If the project is designed per ASCE 7-05 (2009 IBC or earlier), enter the calculated design pressure based on Basic Wind Speed.

ULTIMATE-

ULTIMATE+ i

If the project is designed per ASCE 7-10 (2012 IBC or later), enter the calculated design pressure based on Ultimate Design Wind Speed.

ADDITIONAL INFORMATION

ATTACH ANY RELEVANT DETAILS OR PROJECT FILES

Please write your purpose of inquiry on the right.

Choose Files No files

PURPOSE OF INQUIRY*:

BACK